Click 'Download sample' for the free sample file:

 Download sample

Make/Model Information:

  • Brand:   Icom
  • Models included:
    • Icom D-STAR ID-RP2

File Information:

  • Type:   Factory Service Manual (FSM)
  • Language:   English (EN)
  • Number of pages:   148
  • File size:  ∼ 12.50 MB
  • File Format:   PDF only
  • SME Watermarks:   None
  • Password lock:   No
  • Edit/copy/modify:   Yes
  • SKU:   ROIC-0001

NOTE:  This list was created by program script and may not accurately represent the text from the source pages.   For full preview please click on 'Download sample':

 Download sample

SERVICE
MANUAL
D-STAR REPEATER SYSTEM
S-14205HZ-C1
Nov. 2005
INTRODUCTION
This service manual describes the latest service information
for the ID-RP2 D-STAR REPEATER SYSTEM at the time of
publication.
DANGER
NEVER connect the transceiver to an AC outlet or to a DC
power supply that uses more than 16 V. This will ruin the
transceiver.
DO NOT expose the transceiver to rain, snow or any liquids.
DO NOT reverse the polarities of the power supply when
connecting the transceiver.
DO NOT apply an RF signal of more than 20 dBm (100
mW) to the antenna connector. This could damage the
transceiver’s front end.
ORDERING PARTS
Be sure to include the following four points when ordering
replacement parts:
1. 10-Digit Icom parts number
2. Component name and informations
3. Equipment model name and unit name
4. Quantity required

1130009850 S.IC TC74LCX245FT ID-RP2C MAIN UNIT 5 pieces
8810002950 Screw BiH M36 SUS ID-RP2C Cover 10 pieces
Addresses are provided on the inside back cover for your
convenience.
REPAIR NOTES
1. Make sure a problem is internal before disassembling
the transceiver.
2. DO NOT open the transceiver until the transceiver is
disconnected from its power source.
3. DO NOT force any of the variable components. Turn
them slowly and smoothly.
4. DO NOT short any circuits or electronic parts. An
insulated tuning tool MUST be used for all adjustments.
5. DO NOT keep power ON for a long time when the
transceiver is defective.
6. DO NOT transmit power into a signal generator or a
sweep generator.
7. ALWAYS connect a 50 dB to 60 dB attenuator between
the transceiver and a deviation meter or spectrum
analyzer when using such test equipment.
8. READ the instructions of test equipment thoroughly
before connecting equipment to the transceiver.
To upgrade quality, any electrical or mechanical parts and
internal circuits are subject to change without notice or
obligation.
ID-RP2C
ID-RP2D
ID-RP2V
ID-RP2L
Icom, Icom Inc. and logo are registered trademarks of Icom Incorporated (Japan) in the United States, the United
Kingdom, Germany, France, Spain, Russia and/or other countries.
MODEL DESCRIPTION
ID-RP2C REPEATER CONTROLLER
ID-RP2L
10GHz MICROWAVE LINK REPEATER
Version TX frequency RX frequency
USA 10.150 - 10.175 GHz 10.000 - 10.025 GHz
USA-1 10.000 - 10.025 GHz 10.150 - 10.175 GHz
ID-RP2D 1.2 GHz DATA REPEATER
ID-RP2V 1.2 GHz DIGITAL VOICE REPEATER
TABLE OF CONTENTS
ID-RP2 SYSTEM CONNECTION
ID-RP2C REPEATER CONTROLLER
ID-RP2L 10GHz MICROWAVE LINK REPEATER
ID-RP2D 1.2 GHz DATA REPEATER
ID-RP2V 1.2 GHz DIGITAL VOICE REPEATER
SECTION 1 SPECIFICATIONS
SECTION 2 INSIDE VIEW
SECTION 3 CIRCUIT DESCRIPITON
3-1 RECEIVER CIRCUITS
3-2 TRNSMITTER CIRCUITS
3-3 POWER SUPPLY CIRCUITS
3-4 OTHER CIRCUITS
SECTION 4 PARTS LIST
SECTION 5 MECHANICAL PARTS AND DISASSEMBLY
SECTION 6 SEMI-CONDUCTOR INFORMATION
SECTION 7 BOARD LAYOUTS
7-1 MAIN UNIT
7-2 LED UNIT
SECTION 8 WIRING DIAGRAM
SECTION 9 BLOCK DIAGRAM
SECTION 10 VOLTAGE DIAGRAM
10-1 MAIN UNIT
SERVICE MANUAL
REPEATER CONTROLLER
faJomO`
SECTION 1 SPECIFICATIONS
SECTION 2 INSIDE VIEWS
SECTION 3 CIRCUIT DESCRIPITON
3-1 RECEIVER CIRCUITS
3-2 TRNSMITTER CIRCUITS
3-3 PLL CIRCUITS
3-4 POWER SUPPLY CIRCUITS
SECTION 4 ADJUSTMENT PROCEDURES
4-1 PREPARATION
4-2 PLL AND BASEBAND ADJUSTMENT
4-3 TRANSMITTER AND RECEIVER ADJUSTMENT
SECTION 5 PARTS LIST
SECTION 6 MECHANICAL PARTS AND DISASSEMBLY
SECTION 7 SEMI-CONDUCTOR INFORMATION
SECTION 8 BOARD LAYOUT
8-1 IF UNIT
SECTION 9 WIRING DIAGRAM
SECTION 10 BLOCK DIAGRAM
SECTION 11 VOLTAGE DIAGRAM
11-1 IF UNIT
SERVICE MANUAL
10GHz MICROWAVE LINK REPEATER
faJomOi
SECTION 1 SPECIFICATIONS
SECTION 2 INSIDE VIEWS
SECTION 3 DISASSEMBLY INFORMATION
SECTION 4 CIRCUIT DESCRIPITON
4-1 RECEIVER CIRCUITS
4-2 TRNSMITTER CIRCUITS
4-3 PLL CIRCUITS
4-4 POWER SUPPLY CIRCUITS
4-5 PORT ALLOCATION
SECTION 5 PARTS LIST
SECTION 6 MECHANICAL PARTS AND DISASSEMBLY
SECTION 7 SEMI-CONDUCTOR INFORMATION
SECTION 8 BOARD LAYOUTS
8-1 MAIN-D UNIT
8-2 LOGIC-D UNIT
8-3 FRONT UNIT
8-4 REAR UNIT
SECTION 9 WIRING DIAGRAM
SECTION 10 BLOCK DIAGRAM
SECTION 11 VOLTAGE DIAGRAMS
11-1 MAIN-D UNIT
11-2 LOGIC-D UNIT
SERVICE MANUAL
1.2 GHz DATA REPEATER
faJomOa
SECTION 1 SPECIFICATIONS
SECTION 2 INSIDE VIEWS
SECTION 3 DISASSEMBLY INFORMATION
SECTION 4 CIRCUIT DESCRIPITON
4-1 RECEIVER CIRCUITS
4-2 TRNSMITTER CIRCUITS
4-3 PLL CIRCUITS
4-4 POWER SUPPLY CIRCUITS
4-5 PORT ALLOCATION
SECTION 5 PARTS LIST
SECTION 6 MECHANICAL PARTS AND DISASSEMBLY
SECTION 7 SEMI-CONDUCTOR INFORMATION
SECTION 8 BOARD LAYOUTS
8-1 MAIN-R UNIT
8-2 MAIN-T UNIT
8-3 LOGIC-R/T UNIT
8-4 FRONT UNIT
8-5 REAR UNIT
SECTION 9 WIRING DIAGRAM
SECTION 10 BLOCK DIAGRAM
SECTION 11 VOLTAGE DIAGRAMS
11-1 MAIN-R UNIT
11-2 MAIN-T UNIT
11-3 LOGIC-R UNIT
11-4 LOGIC-T UNIT
SERVICE MANUAL
1.2 GHz DIGITAL VOICE REPEATER
faJomOs
1-1-32, Kamiminami, Hirano-ku, Osaka 547-0003, Japan S-14205HZ-C1
2005 Icom Inc.


Payment

Before sending payment please download the sample file to verify the following:

  •   Check the Brand, Model and Year.
  •   Review the Table of Contents (TOC).
  •   Review the Bookmarks.
  •   Inspect the quality of images.

7.00USD

Paypal
Credit card*
Debit card**

*Credit card or Debit card processing at Paypal portal.
**Debit card: available only from selected countries/territories.