Click 'Download sample' for the free sample file:Download sample
NOTE: This list was created by program script and may not accurately represent the text from the source pages. For full preview please click on 'Download sample':Download sample
©2005 VERTEX STANDARD CO., LTD. EH017M90B
Exploded View & Miscellaneous Parts
Board Units (Schematics, Layouts & Parts)
This manual provides the technical information necessary for
servicing the FT-60R VHF/UHF Dual Band Transceiver.
Servicing this equipment requires expertise in handing sur-
face-mount chip components. Attempts by non-qualified per-
sons to service this equipment may result in permanent dam-
age not covered by the warranty, and may be illegal in some
Two PCB layout diagrams are provided for each double-sided
board in this transceiver. Each side of the board is referred to
by the type of the majority of components installed on that
side (Side A or Side B). In most cases one side has only
chip components (surface-mount devices), and the other has
either a mixture of both chip and leaded components (trim-
mers, coils, electrolytic capacitors, ICs, etc.), or leaded compo-
While we believe the information in this manual to be correct,
VERTEX STANDARD assumes no liability for damage that
may occur as a result of typographical or other errors that may
be present. Your cooperation in pointing out any inconsisten-
cies in the technical information would be appreciated.
VERTEX STANDARD CO., LTD.
4-8-8 Nakameguro, Meguro-Ku, Tokyo 153-8644, Japan
10900 Walker Street, Cypress, CA 90630, U.S.A.
8350 N.W. 52nd Terrace, Suite 201, Miami, FL 33166, U.S.A.
YAESU EUROPE B.V.
P.O. Box 75525, 1118 ZN Schiphol, The Netherlands
YAESU UK LTD.
Unit 12, Sun Valley Business Park, Winnall Close
Winchester, Hampshire, SO23 0LB, U.K.
VERTEX STANDARD HK LTD.
Unit 5, 20/F., Seaview Centre, 139-141 Hoi Bun Road,
Kwun Tong, Kowloon, Hong Kong
Frequency Ranges: RX 108 - 137 MHz (Air Band),
(Cellular Blocked) 137 - 520 MHz (AM/FM),
700 - 999.990 MHz (FM)
TX 144-148 MHz, 430-450 MHz
Channel Steps: 5/10/12.5/15/20/25/50/100 kHz
Frequency Stability: ±5 ppm @ 14 °F to 140 °F (–10 °C to +60 °C)
Repeater Shift: ±600 kHz (144 MHz), ±1.6/5.0/7.6 MHz (430 MHz)
Emission Type: F2 (F2D), F3 (F3E)
Antenna Impedance: 50 W
Supply Voltage: Nominal: 7.2 V DC, Negative Ground
(Negative Ground) Operating: 6.0 ~ 16.0 V DC (EXT DC Jack)
11.0 ~ 16.0 V DC (EXT DC Jack with Charging)
Current Consumption: 125 mA (Receive)
(Approx. @7.2 V) 45 mA (144 MHz, Standby, Saver Off)
47 mA (430 MHz, Standby, Saver Off)
19 mA (Standby, Saver On)
0.8 mA (Auto Power Off)
1.5 A (5 W TX, 144 MHz)
1.6 A (5 W TX, 430 MHz)
Operating Temperature: –4 °F to 140 °F (–20 °C to +60 °C)
Case Size: 2.3 (W) x 4.3 (H) x 1.2 (D) (58 x 109 x 30 mm) (W/O knob, antenna, and belt clip)
Weight: 13.05 Oz (370 g) with FNB-83, and antenna
RF Power Output: 5.0 W (High) / 2.0 W (Middle) / 0.5 W (Low) (Approx.)
Modulation Type: Variable Reactance F2 (F2D), F3 (F3E)
Maximum Deviation: ±5.0 kHz (F2D, F3E)
Spurious Emission: At least 60 dB down (@ High and Middle power)
At least 40 dB down (@ Low power)
Microphone Impedance: 2 kW
Circuit Type: Double-Conversion Superheterodyne
Intermediate Frequencies: 1st: 47.25 MHz, 2nd: 450 kHz
Sensitivity : 0.8 µV TYP for 10 dB SN (108-137 MHz, AM)
(Cellular Blocked) 0.2 µV for 12 dB SINAD (137-140 MHz, FM)
0.16 µV for 12 dB SINAD (140-150 MHz, FM)
0.2 µV for 12 dB SINAD (150-174 MHz, FM)
0.3 µV TYP for 12 dB SINAD (174-300 MHz, FM)
0.8 µV for 10 dB SN (300-336 MHz, AM)
0.25 µV for 12 dB SINAD (336-420 MHz, FM)
0.2 µV for 12 dB SINAD (400-470 MHz, FM)
0.25 µV for 12 dB SINAD (470-520 MHz, FM)
0.5 µV TYP for 12 dB SINAD (800-900 MHz, FM)
0.8 µV TYP for 12 dB SINAD (800-999.990 MHz, FM)
Selectivity: 12 kHz/35 kHz (–6 dB /–60 dB)
AF Output: 400 mW @ 8 W for 10 % THD (@ 7.5 V)
Specifications are subject to change without notice, and are guaranteed within the 144 and 430 MHz amateur bands only.
Frequency ranges will vary according to transceiver version; check with your dealer.
Exploded View & Miscellaneous Parts
TERMINAL PLATE R
BELT CLIP ASSY
FRONT CASE ASSY
(W/ MIC SHEET,
SP NET,LIGHT GUIDE,
RING NUT (x2 pcs)
RA021080A (Lot. 5 )
RA0210800 (Lot. 1 4)
REAR CASE ASSY
(W/ SMA CNNECTOR)
RA055770B (Lot. 31 )
LATCH NAIL C
RA0123500 (Lot. 1 30)
LATCH NAIL B
The mic element must be desoldered and
removed from the PCB on order to rein
stall its protective rubber cover.
Therefore, be careful
not to remove this
cover unless mic ele
ment replacement is
Non-designated parts are available only as part of
a designated assembly.
TAPTITE SCREW M2X4NI#3
TAPTITE SCREW 2X3.3NI
TAPTITE SCREW M2X4B#3
SEMS SCREW SM2.6X6B
PAD (x2 pcs)
Before sending payment please download the sample file to verify the following:
*Credit card or Debit card processing at Paypal portal.
**Debit card: available only from selected countries/territories.